|
XPROG-M v5.3 plus Dongle |
68 HC908
XC68HC708AZ60 (8 H62A)
0 L72A
3 K56G
0 L07H
0 L59XZ, speaking, reading and writing, support network security box down from the reading and writing
Siemens IMMO new 0 L72A E security box down from reading and writing
MingRui SRS computer 1 L02M literacy and the wiring diagram
1 J35D (68 HC908AZ60) EEPROM of reading and writing
|
|
|
|
|
|
|
Xprog box V5.50 ecu programmer |
The XPROG-box project is a continuation of the project XPROG and now supports more than 450 units (serial EEPROM's, Microcontrollers (MCU), Electronics Control Units (ECU), DashBoards, Immobilizers, Calculators and others).
|
|
|
|
|
|
XPROG-Box V5.48 |
The XPROG-box project is a continuation of the project XPROG and now supports more than 450 units (serial EEPROM`s,
Microcontrollers (MCU), Electronics Control Units (ECU), DashBoards, Immobilizers, Calculators and others).
|
|
|
|
|
XPROG BOX V5.45 |
The XPROG-box project is a continuation of the project XPROG and now supports more than 450 units (serial EEPROM`s, Microcontrollers (MCU), Electronics Control Units (ECU), DashBoards, Immobilizers, Calculators and others).
|
|
|
|
|
UPA USB PRO V2013 Full adapters |
Upa-usb 2013 is the full set with all adapters,The main Device can be directly connected to the Elrasoft.com UUSP (UPA-USB Serial Programmer) or by an optional DB9 male / female 1:1 extension cable. It's equipped with an 40pin ZIF Socket for all narrow and wide DIP / DIL devices as well as with a 16 pin SOIC ZIF (150mil, narrow) socket to cover most commonly used devices.
|
|
|
|
|
UPA USB PRO V2012 Full adapters |
Upa-usb 2012 is the full set with all adapters,The main Device can be directly connected to the Elrasoft.com UUSP (UPA-USB Serial Programmer) or by an optional DB9 male / female 1:1 extension cable. It's equipped with an 40pin ZIF Socket for all narrow and wide DIP / DIL devices as well as with a 16 pin SOIC ZIF (150mil, narrow) socket to cover most commonly used devices. |
|
|
|
|
ETL-TMS Programming tool |
Supported devices:
TMS370CX6X
TMS370CX5X
TMS370CX4X
TMS370CX3X
TMS370CX0X
TMS375C006
TMS374C003A
TMS374C013A
|
|
|
|
|
Renault ECU decoder |
From the year 1994 most Renault cars are equipped with engine immobilizer system and it makes replacement of injection computer more complicated. There is no problem if replacement ECU is bought from Renault service dealer - it is sold with no immobilizer code stored, but replacing damaged computer with used one is impossible because of mismatch of unlocking codes.
|
|
|
|
|
Carprog universal EEPROM tool |
Carprog universal EEPROM tool is a universal EEPROM tool that allowes to read, write, edit and erase various types of EEPROM memories. I2C, SPI and Microwire memory interfaces are supported. Device is communicating with PC through USB port. It allowes you to fully adjust main programming parameters like programming voltage, pull-up resistors, clock speed and read/write delays. It can load, edit and save files in *.bin, *.epp, and *.sec formats. CodiProg USB software includes ability to upgrade device firmware to enable support for new memory types. It is also possible to use CodiProg erasing function without PC computer control. |
|
|
|
|
TMS374 ECU Decoder |
This Tool is a frequency sweeper with 5V square wave output (Duty cycle 50%, effective frequency range from over 10kHz (max 50kHz) to 50Hz) .This tool can be also considered as a MCU version of the software TMS-374 Decoder ECU. The only difference between the two tools is that the MCU version works without a PC. |
|
|
|
|
UUSP (UPA USB Serial Programmer) Full Package V1.2 |
- USB 2.0 and 1.1 compatible
- No power supply required
- 6 general purpose I/Os, overcurrent and overvoltage protected (12V/10mA)
- One 3.3/5V power supply output max 150mA, overcurrent protected
- One 8-13V/1mA output, program controlled
- Supports 3.3V and 5V devices
- Motorola HC11 Config Register Programming
- Self-Test option
- Can be used with BDM Lockout Disable Adapter
- Small dimensions 5.5x8.5cm
|
|
|
|
|